Analysis of the Skills of Initiating Sliding Bearings (II)

Source: Bearing network time: 2018-03-16

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

The reason for the entry of fine particles is as follows: First, the filter function of the air filter is poor or the sealing of the air intake system is not good; the pipelines and joints of the intake system should be checked; whether there is a break or looseness; whether the filter element is loose or not, Whether the paper core is broken or not. Whether it is repair or protection is the protection of the entire air intake system is very important; it is necessary to ensure reliability. Second, after the smooth oil is contaminated, participate in the launching machine or the oil and the filter element is used for a long time. Blocked; so that the smooth outer surface of the oil does not filter directly into the filter element. Third, the fuel supply is too large for incineration, nozzle leakage; the formation of fuel into the crankcase; together with some impurities into the crankcase with fuel and The oil mixes together to reduce the smoothing effect. Therefore, the launching machine should pay attention to investigating the smoke exhaustion and working condition of the initiator in the application; if there is an abnormality, it should be checked and corrected in time to correct or replace it. Fourth, when the initiator is assembled; the internal parts are sanitized. Degree difference. When repairing and protecting the initiator; must pay attention to the hygiene of the parts; the device should pay attention to avoid re-contamination; ensure the internal hygiene after the device.
No matter what kind of reason; it is necessary to replace the engine oil and the filter element after the fault is removed. The repaired machine initiates an empty work for two hours to stop the work for inspection; there is no alloy powder in the oil; However, it is necessary to pay attention to the investigation in the first few days of application; after 60 to 120 hours of work, it is confirmed that the abnormal wear is completely removed; the oil is replaced; the initiator can be put into normal use. If abnormal wear is continued, it is necessary Aborting the application for crash viewing and correction.
2. Damage to the bearing pad by larger particle foreign matter and residual smooth oil:
When large particles of alloy blocks or flakes are found in the oil filter element and the initiating oil sump; the shaft and the bearing bush have been severely damaged; it is necessary to stop the inspection and correction immediately; if it is continuously used, more parts will be damaged. .
The reason for the entry of larger particles is that the parts are not cleaned when the device is installed; for example, the metal chips that occur when processing the inner hole of the connecting rod bushing remain in the oil passage of the connecting rod, the cutting or sediment is stuck in the parts and the oil passage, and the cutting is not completed before the device. Or the machining burrs of the machined parts associated with the moving surface are not removed, the foreign objects with larger particles sticking to the bearing bushings or the outer surface of the shaft are damaged. These images are very serious for the damage of the bearing pads. Carefully clean up and view the device.
The smoothing effect and heat dissipation of the residual smooth oil can not meet the demand; the bearing and the shaft wear are aggravated; the alloy with excessive surface temperature is melted and damaged, and the oil of the residual smooth oil is more blocked. The smooth oil rich in impurities directly enters the moving surface without filtering; further accelerates the damage of the shaft and the bearing bush. Therefore, when purchasing and replacing the smooth oil, the quality of the smooth oil must be strictly controlled according to the rules; the smooth oil is selected according to the rules.

Recommend to friends comments close window

Bearing related knowledge

Sliding bearing scraping skill needs pump bearing protection "detailed analysis"
Bearing and bearing steel skill requirements and production levels
SKF aviation rolling bearing skills (2)
What are the methods to control the influence of bearing noise?

This article links to http://
Please indicate China Bearing Network http://

Previous:Rolling bearing residual magnetic skill conditions (2)
Next: How does the residual magnetism of the bearing occur?

API 6D Trunnion Mounted Ball Valve

API 6D trunnion mounted ball valve, cast steel WCB trunnion mounted ball valve, LCB trunnion mounted ball valve, CF8 trunnion mounted ball valve, CF8M trunnion mounted ball valve, 3pcs body trunnion mounted ball valve, side entry trunnion mounted ball valve, top entry trunnion mounted ball valve, forged steel A105 trunnion mounted ball valve, LF2 trunnion mounted ball valve, F304 trunnion mounted ball valve, F316 trunnion mounted ball valve, F316L trunnion mounted ball valve, F51 trunnion mounted ball valve, soft seat trunnion mounted ball valve, metal to metal seat trunnion mounted ball valve, seat pocket clading trunnion mounted ball valve, gear operated trunnion mounted ball valve. fire safety trunnion mounted ball valve, NACE MR 01-75 trunnion mounted ball valve, trunnion mounted Ball Valve Components

Trunnion Ball Valve,Trunnion Valve,Trunnion Mounted Valve,Trunnion Type Ball Valve

SUZHOU RSF VALVE CO.,LTD , https://www.rsf-valve.com