TPV/TPE Granules with Cheap Price From Jiangsu Nanjing

• Model NO.: 6000
• Plastic Properties After Heated: Thermoplastic Plastics
• Color: White
• HS Code: 4002991100

• Material: TPV
• Plastic Forming Method: Extrusion
• Process: Injection, Extrusion, Blow Molding

Pacrel ® TPV 6000
Pacrel ® TPV is a Vulcanised Thermoplastic Elastormer. It is made up of an elastomeric phase (dynamically vulcanised EPDM), which is deeply dispersed in a polyolefinic thermoplastic matrix, whose combination determines a real plasto elastomeric alloy characterised by high performances and extremely easy processability. Its thermoplastic matrix allows Pacrel ® TPV to be processed in an easy and unexpensive way by means of traditional technologies used for thermoplastic materials and to be fully recyclable whereas its elastomeric phase features typically rubber-like specifications such as elastic recovery and softness.
 
Applications: seals and gaskets, hand grips, auto parts, wire and cable sheath/ connector, transportation expansion joint, electric and electronical products and so on.
 

 Main specifications:
Wide hardness range, from Shore40A to 95A (50D)
Typical density <0.96 g/cm3
High elastic recovery within a wide temperature range
Excellent resistance to UV aging and ozone
Service temperature ranging from -60 to 135°C
Excellent resistance to several chemical agents
High fatigue resistance
High thermal and electric insulation values
Heat adhesion on polypropylene (PP)
Excellent colorability
 

Process: Can be processed through typical thermoplastics technologies, such as injection-molding, extrusion, blow-molding, calendering and over-molding. Normally Pacrel does not require drying before processing, apart from some special grades.
 
Recycling: Can be completely recycled and reused after regrinding.
The user shall always verify that the compound obtained by mixing virgin and reground material is suitable for the specific application and meets the requirements. 
  
Storage: Should be stored in a covered facility and kept away from moisture and heat.

Certifications: 

 

High-Mast Lamps Series

The High-mast Lamp is generally refers to the new lighting device which is composed of the steel taper light pole and the high power combination lamp frame of 15 meters or above.It consists of lamp holder, internal lamp, electric rod body and basic part.Lamp head modelling can according to user requirement, surroundings, lighting need specific and definite;The interior lamps are mainly composed of floodlights and projection lamps. The light source adopts NG400 high pressure sodium lamp, and the lighting radius is 60 meters.The bar body is usually a pyramid structure, which is made of steel plate, with a height of 15 to 40 meters, which consists of two to three sections.

Material characteristics

1. Beautiful appearance, large lighting area, good lighting effect, concentrated light, uniform illumination, small glare and easy to control and repair.

2. Applicable places: city square, station, wharf, highway, stadium, overpass, etc.

3. The lamp pole is a high quality steel plate by moulding into a multi - pyramid splicing steel rod, through hot galvanizing anti-corrosion treatment.

4. The lamp frame is made of high quality stainless steel.

5. Fasteners bolts and nuts are stainless steel.

6. Light source:400W-1000W sodium lamp.

Specifications:

Height: from 18m to 50 m

Suit for: highway, expressway, parkway, freeway, central motorway junction, truck and bus terminals, railyards, ship docks, airports, ferry terminals, prisons, industrial and commercial sites, international borders.

Shape: round, multi-pyramidal, column form, polygonal or conical

Material:

Q345B/A572,minimum yield strength>=345n/mm2
Q235B/A36,minimum yield strength>=235n/mm2

Tolerance of Dimension: ±2%

Lighting Source: 400 W- 5000 W high pressure sodium flood light, light extension :up to 30 000 m²

Light plate: Various figure of selection ,material with hot dip galvanization steel frame

Lifting System: Lifter fixed in the inner of the pole with lifting speed of 3~5 meter per minute
Equipped e; ant ferromagnetism brake and break -proof device, manual operation applied under power cut

Electric Appliance Control Device: Electric appliance box to be the hold of the pole ,lifting operation could be 5 meter away from the pole through wire .Time control and light control could be equipped to realize full-load lighting mode and part lighting mode

Surface treatment: Hot dip galvanized Following ASTM A 123, color polyester power or any other standard by client required.

Joint of Poles: Insert mode, inner flange mode, face to face joint mode .

Design of pole: Against earthquake of 8 grade

Wind Speed: 80 Km/Hour

Welding: We has past flaw testing. Internal and external double welding makes the welding in shape

Thickness: 6 mm to 20 mm

Production Process:
Raw material test→Cutting→Molding or bending →Welding (longitudinal ) →Dimension verify→Flangewelding→Hole drilling →Calibration →Deburr →Galvanization or powder coating, Painting→Recalibration→Thread→Packaging

Packages: Our poles as normal cover by Mat or straw bale at the top and bottom ,anyway also can following by client required

High-Mast Lamps Series,High Mast Lamps,High Mast Light,High Mast Light Pole

Jiangsu chengxu Electric Group Co., Ltd , https://www.chengxulighting.com