The problems of anti-taste, yellowing, water leakage, blockage, displacement, slow watering, and unclean washing are often plagued by us during the daily use of the toilet. How to solve these six major problems? Here is a detailed solution. Toilet anti-flavor reason 1 The flange of the toilet and the pipe mouth are not tightly sealed, which is one of the culprit of odor. When installing, the material should be embedded with grease and other materials in front of the drain outlet. If the interface is sealed, the odor may be emitted from the floor tiles. 2 The bottom sealant of the toilet is not tight, causing the smell to return. 3 The floor tiles around the toilet are not tightly sewn, and the smell is returned. 4 The toilet lid is not tightly sealed, causing the smell to return. 5 See if the water seal of the toilet is enough. Generally, after the toilet water is washed, there is a certain water seal to ensure the isolation of the pipeline. If the water seal is broken, you have to change the toilet at this time. 6 When installing, there is no good sealing and sealing of the sewage pipe and the toilet outlet, and it is easy to have odor to run out. Solution 1The floor tiles around the toilet are empty, first repair the empty floor tiles. 2 Use glass glue to make a circle on the bottom edge of the toilet to keep it sealed. 3 Cover the toilet cover in time after going to the toilet. 4 Always flush the toilet with water, so that there is no stagnant water or degraded water in the trap. 5 Use the toilet to clear the agent: During the interval, you can pour the appropriate amount of toilet into the toilet, cover the toilet cover for a while, then rinse with water to keep the toilet open. 6 A small cup of balsamic vinegar can be placed in the toilet and the smell will disappear. It is valid for six or seven days and can be changed once a week. Or dry the residual tea leaves and put them in the toilet or ditch to burn them, which can eliminate the stench. Toilet yellow toilet lid yellow This has something to do with the material of the lid and is also related to daily maintenance. In the past, there were many ABS materials on the market, which were easy to turn yellow. Nowadays, the market is mainly made of PP materials. These materials are more resistant to color than ABS, and relatively less likely to turn yellow. There is also a UF material. Solution It is recommended to select the cover of the latter two materials when changing the toilet lid. In daily maintenance, care should be taken not to let the sun shine directly on the toilet lid, and sunlight may easily cause discoloration. You can use toothpaste to clean when cleaning. The inner wall of the toilet is yellow The toilet takes a long time, the scale, the urinary scale and so on, and the inner wall of the toilet will be yellow. Solution 1 old stockings: first spray the foaming detergent in the toilet, then roll the old stockings on the stick to brush, you can completely remove the dirt inside the toilet. 2 Coke: Pour carbonated drinks such as cola into the toilet and wash it. The effect is not bad. 3 vinegar: white vinegar is acidic, and the odor factor of the toilet is alkaline. When the two meet, a neutralization reaction will occur. Just put the white vinegar in the mineral water bottle, then poke a few small holes under the water bottle, and then put the bottle in the water tank normally. The vinegar can flow out with water every time it is flushed. Not only can the toilet wall be yellowed, but also effectively deodorize, the water tank can also save water by putting a bottle. 4 with 84 disinfectant. The main component of 84 disinfectant is sodium hypochlorite (NaClO). Sodium hypochlorite is highly oxidizing and can oxidize and denature most substances, thereby enabling disinfection. Sodium hypochlorite reacts chemically with carbon dioxide in the air to produce hypochlorous acid (HCIO) HCIO is an acid that is corrosive. The main component of scale and urinary scale is calcium carbonate (CaCO?). Cleaning the toilet with 84 disinfectant can not only remove scale and urinary dirt, but also disinfect. The specific cleaning operation is as follows: Slowly pour the 84 disinfectant along the inner wall along the inner wall. After half an hour, brush it with the toilet brush. The toilet can be bright and clean. Then pour the laundry liquid into the toilet. The toilet is not only bright and fresh, but also has a faint scent. Toilet leaking Generally speaking, there are many reasons for the leakage of the toilet, except that the drain valve is not tightly sealed in the water tank fittings, and the quality of the toilet itself is not good. the reason 1 Inferior material: Some manufacturers blindly reduce the production cost. The inferior material is used to cause the water inlet of the inlet valve and the inlet pipe to crack when injection molding, resulting in failure of the seal. The water in the water tank flows into the toilet through the overflow valve overflow pipe, resulting in “long flowing waterâ€. ". 2 Water tank fittings miniaturization: excessive pursuit of miniaturization of water tank fittings, resulting in insufficient buoyancy of the floating ball (or floating bucket). When the water floods the floating ball (or floating bucket), the inlet valve cannot be closed, so that the water keeps flowing. The water inlet tank finally flows into the toilet from the overflow pipe to cause water leakage. This is especially true when tap water pressure is high. 3 Water tank accessories interference: Each mechanism of the water tank fittings interferes during the operation, resulting in water leakage. For example, when the water tank is discharged, the float ball and the float rod fall, which affects the normal reset of the flap, resulting in water leakage. In addition, the float rod is too long, and the float ball is too large, causing friction with the tank wall, affecting the free rise and fall of the float ball, resulting in seal failure and water leakage. 4 The sealing of each connection of the drain valve is not strict: the non-disposable forming drain valve is not tightly sealed due to the joint. Under the action of water pressure, water flows into the toilet from the interface gap through the overflow pipe, causing water leakage. The lifting inlet valve can be freely changed in height. If the sealing ring is not tightly matched with the pipe wall, water leakage often occurs. 5 sealing ring is not tight: if it is leaking from the bottom of the toilet after flushing in the toilet, and the water is unclear and smelly, then it can be judged that the sealing ring on the drain pipe at the bottom of the toilet is not sealed. The sealant on the edge of the toilet and the ground is not tightly sealed, and the dirt is reversed in the case where the drain pipe is not smooth. You can first confirm whether the drainage pipe is not smooth. If the pipe is not smooth, you should first clear the pipe and then let the product seller reinstall the toilet. Most of this happens shortly after the toilet is installed. 6 There is a crack in the toilet: If it is found that there is water seepage from the surface of the toilet at any time, then it is suspected that there may be cracks in the toilet. The test method is: first turn off the inlet valve, then drain the water in the toilet tank. Clean, then add the red ink or colored ink to the water left in the tank and stay for about 30 minutes. Observe whether or not there is oozing colored ink. If there is any, it can be concluded that there is a crack in the toilet. This situation cannot be repaired. Repair is also a problem. The only way is to replace it. Solution 1 Check if the flush switch is reset. Some plastic toilet flushing switches have been worn for a long time and occasionally get stuck and can't be regained. It is usually reset by repeating the switch several times. Check if the rubber gasket under the ball valve is aging, the seal is not strict, and the problem needs to be replaced. 2 Check whether the connection between the spherical float and the water inlet switch of the water tank is loose, the float is in place and the switch is not closed, so that the water does not stop, and the water flows out from the upright drain pipe when the water is full, as long as the connection between the float and the water valve switch is tightened. can. If the rubber ball valve is damaged, the seal is not strict, and water leakage occurs, and it needs to be replaced immediately. 3 water tank leakage, basically the problem of the drain valve, check the water plug of the water tank outlet, if the rubber plug of the water outlet is damaged or blocked by foreign matter, the plug is not tightly sealed, and the toilet water will not stop. If the water supply pipe in the water tank is placed incorrectly, it will affect it more or less. Tips: If the interface between the toilet suction port and the down pipe leaks and leaks, it is best not to repair it yourself. It is recommended to have a professional plumber to repair it. The toilet is clogged and the toilet is slightly blocked It is usually a toilet blockage caused by toilet paper or sanitary napkins, towel rags, etc. This can be dredged directly by using a pipe dredging machine or a simple dredging tool. Solution 1 caustic soda, oxalic acid: Many times the toilet is flushed, and it will pass, especially if it is soluble or can be scattered in soil or paper. If it is greasy, then wash it with a pot of boiling water. Or buy some caustic soda, boil water to melt the caustic soda, pour into the toilet, it will pass in ten minutes. Or use an appropriate amount of oxalic acid to dredge (usually you can also clean the toilet with oxalic acid, just neutralize the urine to make the toilet open). 2 wire: use a wire to make a hook and stretch into the sewer mouth to stir, so that the dirt is wrapped around the wire, and then pull out the wire to drag the dirt out of the sewer. Or find a half-inch wide bamboo strip into the toilet to clear. 3 mop, leather tweezers: Put half of the water in the toilet, use a circular mop or a soft-headed brush to align the hole in the sewer. You can also use that kind of old-fashioned mop. After loading half of the water, use a mop to push it into the hole a few times. Move quickly and rely on pressure to get it through. Or go to the market to buy a donkey, then mammoth a few times, once every half a month, it will not block. 4 Beverage bottle: Use the bottle to clear the bottle, cut off the bottom of the bottle of the big cola, and put it in the toilet. Hold the bottom and pull it up a few times. 5 pump: wrap the rag on the pump, then pour some water into it, and start to pump for a while will clear. 6 Hose: Find a hose and connect the tap water to the other end. Pack the rag into the sewer pipe, then open the tap water. The principle is that the pressure of tap water is about 4Mpa, which can completely open the sewer. Remember not to let the hose leak at both ends to maintain the highest pressure. 7 toilet: use the toilet, this is a tool specially designed for the blockage of the pipe. The front end of the toilet is a flexible spring. The length of the spring is determined according to the height of the block from the height of the toilet. After tightening the screw, the internal force is applied to the pipe. Press the spring until it is dredged or the dirt is removed. 8 pipe dredging agent: using pipe dredging agent, which is a kind of powder dredging product that can be used for any pipe dredging. The dredging agent is put into the amount of about 50 grams each time in three times, at intervals of 1-3 minutes, until all the inputs are completed. After staying for three minutes, rush into hot water, and finally stay for 10 minutes, rinse with water, after this operation, it should be able to play the role of toilet clearing. Toilet blockage Carelessly fall into plastic brushes, caps, soaps, combs and other hard objects when using. This kind of clogging can be directly used to directly clear the pipe dredging machine or simple dredger. In severe cases, the toilet must be dismantled. This situation can only be solved by simply getting things out. The toilet is aging blocked When the toilet is used for a long time, it will inevitably cause scaling on the inner wall. In severe cases, it will block the air outlet of the toilet and cause the toilet to be slow. The solution is to find the vent hole to scrape off the dirt and let the toilet water flow smoothly. Toilet installation error Generally, it is divided into: the bottom outlet is not aligned with the drain, and the screw hole at the bottom of the toilet is completely sealed, which may cause the toilet water to be unsmooth, and the toilet tank water level is not high enough to affect the flushing effect. Pit change toilet Some old houses are equipped with squat pits when building houses. U-shaped waterproof elbows are used at the bottom of the sewer pipes. When transforming into toilets, it is best to replace the bottom elbows with direct bends. If you can't change them, then install them. Be sure to do the bottom anti-bend cleaning work before the toilet. Do not let the cement or tile fragments fall into the installation. Professional Moving Head Lights,Dj Moving Head Lights,Led Moving Head Light,Beam Moving Head Light Big Dipper Laser Science And Technology Co., Ltd , https://www.bigdipper-laser.com