Our LED Emergency Twin Spot Lights are a cost effective replacement for old fashioned halogen emergency twin spot fittings. Due to the low power consumption of the LED lamps, only one battery is required, reducing option during charging. The super bright adjustable heads make this twin spot ideal for commercial and industrial applications. with a self test feature every 90 days to ensure correct operation. The Led Emergency Lights design makes it quick and simple to install. Twin Spot Emergency Light,Emergency Twin Spot,Led Twin Spot Emergency Lights,Led Emergency Twin Spot Light Foshan Nai An Lighting Electric Co.,ltd , https://www.naipsled.com
The following is the Shenzhen Hongshunmeng company: the steps to standardize the installation monitoring project
Monitor installation base
First, determine the camera position
1. First, carefully observe the topography of the areas that need to be monitored to determine which are the key areas, and communicate with the customer to confirm the location and size of the required monitoring.
2. According to the terrain and the difficulty of supporting the bracket to choose the specific fixed position of the bracket, it is necessary to comprehensively consider whether to block the camera, beautiful, can be fixed, security and other factors.
3. The area to be monitored by the customer is the basic consideration to ensure that the customer's needs are met, and then other factors are considered.
4. According to the distance to determine the camera to choose a suitable focal length, to ensure the monitoring range and the most suitable for clarity.
Second, the wiring
1. Determine the specific route
a. First with the customer to determine the location of the recorder.
b. Observe the distance and terrain of the video recorder to the location of each camera.
c. Consider the degree of ease of wiring and wire consumption, try to focus the lines of several cameras together to wear a wire tube.
d. If a certain number of cameras are far away from the VCR and are relatively concentrated, consider taking the switch and the front end to collect power.
e. Follow the position and walk through the wiring ideas in your mind.
2. Wiring implementation
a. Ratio line: according to the determined wiring route, pull out the network integration line of each camera to the distance of the recorder from the route length, and reserve more than a few meters in length to avoid the line being too short.
b. Wiring ducts: Use a steel wire or a strap to secure the wire tube to the wire to be routed, and the wall is used to secure the wire tube.
c. Pull the cable: Use a threaded wire to pass through the main trunk or a longer wire tube, use a tape to thread the head of the wire and the end of the wire to be threaded, and pull the wire through the wire tube. The relatively short tube is threaded or threaded and then the tube is fixed. Remember to wear straight, bend, and three links.
d. Note: 1 pay attention to keep the length of the front and rear lines when pulling the cable
2 Pay attention to whether or not the wiring route will affect the mobility of the door and window of the switch. 3 The wiring at the height should pay attention to the safety of its own and the safety of the customer's property, and be as careful as possible.
Third, camera installation
1. Strike the bracket: Mark several points of the screw with a marker pen according to the position of the bracket, drill a certain depth with the impact drill at the marking point, hammer the rubber plug into the drill hole, and then use a screw to screw the bracket up. If you can't drill, consider using a harder wire to fix the stent by binding.
2. Install the camera: Tighten the camera onto the bracket. Be careful not to let the camera shake freely.
3. Trimming head: Cut the front-end network power wire to the appropriate length, cut out the wire and cable, connect the wire head and press the wire head, the wire connects the male head, pay attention to the positive and negative wires and the network cable wire sequence.
4. Terminal: Connect the camera head to the net and wrap the head with tape. If the outside is considered to be waterproof, make sure the tape is covered with several layers of tape, then hide the head under the bracket and fix it with wire or tape.
5. Adjust the angle of the camera to a suitable location and tighten the screws.
Fourth, back-end connection and debugging
1. Cut the end of the back-end line and connect the recorder, switch, power supply, and monitor.
2. Observe whether the lights of the switch are bright, insert the notebook for debugging into the switch, set the ip address of the connected camera, find out the position of the unconnected camera, check the reason, check whether there is any power and check again. The internet. The reason is that most of the wire or cable is not connected, re-wiring and try again.
3. After troubleshooting, set the IP address and add it to the VTR channel.
4. Carefully adjust the angle of the camera according to customer needs.
Brief introduction: Shenzhen Hongshunmeng Intelligent Technology Co., Ltd. is a technology-based enterprise specializing in the design, development, production and sales of intelligent channel gates. The company has established a good cooperative relationship with many customers at home and abroad, and offers customers the most favorable price. Provide the best quality products.
The company's main production: wing gates, three roller gates, swing gates, full height turnstiles, translation gates, word gates. At the same time years of research and development and innovation, so that their own products continue to improve, to channel gate as the core, integrated electronic tickets, access control attendance, club consumption / catering, anti-static, fingerprint, palm print, face recognition, iris recognition and other products Integration applies to factories, property communities, schools, supervision areas and other places.
Shenzhen Hongshunmeng Intelligent Technology Co., Ltd. is striving for perfection of every product by following the "pursuit of details" and "humanization" design philosophy, meeting various functional requirements, maximizing easy integration, easy installation, and easy maintenance. , Make intelligent products in the lead level.
From the beginning to the end of the company in the "integrity, dedication, truth-seeking, innovative" business philosophy, adhere to the "people-oriented, scientific management" management philosophy, "customer first, the credibility of the first" quality service has won the recognition of our customers and trust. We firmly believe that "integrity" is the cornerstone of a company's long-term development and an important embodiment of the company's corporate culture. The company will use "honesty" as its cooperation concept to provide customers with quality services.