In the twinkling of an eye, at the end of the year, several things that must be mentioned at the end of the year are nothing more than Spring Festival travel, anti-theft and anti-theft. Combined with decoration, Xiao Bian came to you today to talk about the decoration and cutting materials. No one is perfect, gold is not enough. Occasionally, there are some companies and workers who don’t fly in the decoration. It’s always right to be more than one eye. The top ten in the list of cutting corners, officially announced today! Cutting corners list - 1, substrate processing Steal workers index: ★★★★★ Phenomenon: Before applying latex paint and paving wall tiles, be sure to do the substrate treatment. Some workers cut corners and cut materials in this regard during construction, and the unevenness caused uneven wall surface. After the paint is applied, there is a color difference. When the paint is applied, the paint is discolored and peeled off, or the ceramic tile is not firmly bonded. Reminder: In the paving construction of wall tiles and floor tiles, tiles cannot be directly laid on the surface of lime mortar or latex paint, but the base layer must be cleaned before being laid. When applying latex paint, be sure to pay attention to whether the shading of the wall putty is even and smooth, whether the sanding and rolling are in place. Cutting corners list -2, ground leveling Steal workers index: ★★★★★ Phenomenon: Some houses are not well-grounded and need to be re-leveled during the renovation. If the workers are not careful or deliberately rigged, it will cause the problem of “more and more inequalityâ€. Reminder: First, do a good job on the ground surface treatment, then pour cement mortar to level the ground. Use a dedicated level to determine the flatness of the entire floor, and then proceed to the next step. Cutting corners list - 3, facet processing Steal workers index: ★★★★☆ Phenomenon: "Small face" is a small place that ordinary people can't see and can't pay much attention to, such as the upper edge of the door, the underside of the window sill, the inside of the heating cover, etc. Some workers will cut corners here. It will even do nothing. Reminder: Remember not to ignore any details when checking the quality of your project. Cutting corners list -4, wire wear tube Steal workers index: ★★★★☆ Phenomenon: In the home improvement construction, almost all wires are put in PVC pipes and buried in the walls. After the wires were put into the PVC pipe, the owner couldn't see it at all, and it was difficult to replace it. If the worker is not careful in the operation, it will cause the wire to kink in the tube, causing electricity hazards. If workers cut corners, they will use wire with connectors or put several wires in the same PVC pipe. Reminder: It is best for the owner to purchase the wires or specify the brand. Then supervise the worker's operation on the site, and check the power-on after installation. In addition, the decoration company must leave a "pipeline map." When the electrician had just buried the wires in the wall, he could number the walls and draw a floor plan. Then he used the strokes to draw the direction of the wires and the specific location of the wires, indicating the position on the floor, the ground and the adjacent wall. In particular, the position of the joints of the pipelines should be marked so that in the event of a fault, the line position can be found immediately. Cutting corners list - 5, seam modification Steal workers index: ★★★★ Phenomenon: In some places where the wall meets the door and the window, and where the two different colors of paint are docked, it is also where the workers often perfunctory. We often see mixed paint between latex paint and wood, and various problems at the joints. Reminder: The treatment of joints is very important. We must supervise the workers' construction. If there are two colors of paint on the wall facing each other, it is necessary to apply adhesive tape on the edge of the first color during construction, and then apply another color of paint on it, so that the construction is completed. After tearing off the tape, the entire seam can be very neat. Decoration tricks common means of cutting corners Thermal Insulation Vacuum Glass
Compared with the ordinary insulating glass, the thermal insulation vacuum glass from ICESUN has good sun-proof and heat insulation performance. When the sunshine is exposed through the window in summer, the Low-E coating in ICESUN vacuum glass products can effectively reflect infrared rays and block the heat out of the window. The vacuum degree between the glasses is 10-4 Pa, so the thermal convection no longer exists, the heat conduction is reduced to the limit, and the Low-E layer reflects more than 95% of the infrared radiation. Therefore, the heat between the inner and outer glass plates cannot be exchanged, achieving excellent thermal insulation effect. Just turn on the air conditioner for a short time every day to ensure the cool of the indoor day. So Energy Saving Vacuum Glass can not only save electricity, but also keep users away from the trouble of air conditioning diseases. Besides, ICESUN Vacuum Glass LTD. has also released a series of energy saving vacuum glass for environmental protection, including Sound Proof Vacuum Glass, Anti-radiation Vacuum Glass, Sun Proof Vacuum Glass and so on.
Thermal Insulation Vacuum Glass,Thermal Insulation Glass For Windows,Thermal Preservation Vacuum Glass,Heat Insulator Vacuum Glass ICESUN VACUUM GLASS LTD. , https://www.icesunvacuumglass.com
1 2 Next> Total 2 Page
Page to page