1. Floor-mounted materials and main equipment: Long wood floors should be made of Korean pine, spruce, or wood that is resistant to abrasion, corrosion, and cracking. The width of each slab should not exceed 120 mm. The thickness should meet the design requirements. The side should have a high porosity and the top should be planed. The wood species used in the parquet wood layer shall be selected according to the design. When the design is not required, the quality of the wood, such as manchurian ash, walnut, eucalyptus, etc., shall be good, and the wood that is not easily decayed and cracked shall be used to make joints, kerfs or flat joints. . The length, width and thickness of the parquet should meet the design requirements. Strips and pieces of wood should have a commodity inspection certificate. The anti-corrosion treatment shall be carried out on the wool floor under the double-layer board, the wooden joists on the wooden surface, and the studs. The specifications and dimensions shall meet the design requirements. The project's wool floor is laid with blockboards. Hardwood skirting board: Width and thickness should be processed according to the design requirements. The moisture content must not exceed 12%. The back surface should be coated with preservatives. The pattern and color should be the same as the surface floor. All the baseboards of this project are made of lining fine wood board and walnut wood slice board pressing 15*10 solid wood edge strip production form. Other Materials: wooden wedges, moisture-proof paper, sodium fluoride or other anti-corrosion materials, galvanized iron wires 8 to 10, 5 to 10 cm nails, dowels, galvanized wood screws, lmm thick steel pads, sound insulation materials, etc. Main equipment: Axe, hammer, punch, chisel, screwdriver, square ruler, steel ruler, cutting angle ruler, ink fountain, small chainsaw, small electric planer, **** drill, planer floor machine, floor grinder, hand saw, hand Planer, single-line planer, whetstone, etc. 2, operating conditions: After the plastering of the wall and the top is finished, the +50cm level elevation line has been played. Waterproofing of the roof and floor pipelines have been completed and the pipes and holes have been plugged and compacted. The electricity pipe buried in the ground has been completed. Warm and sanitary pipelines were tested for water and pressure was completed, and they have passed inspection and acceptance. The horizontal lines of the kickboards were played around the room, and wooden bricks with fixed wooden kicks were embedded (must be preserved). All wood materials that come into contact with concrete or brick wall bases, such as wooden joists, backs of baseboards, floor undersides, scissor supports, wooden wedges, wooden bricks, etc., are pre-coated with wood anti-corrosion materials. When the wooden floor adopts the empty paving method, a well-defined ridge wall is constructed according to the design requirements, and each wall is left with 120 ventilation holes of 120 mm×120 mm, and a good wire is pre-embedded and a waterproof mortar is applied to the wall entry. When the wooden floor is used in a solid paving method, a good wire is pre-embedded in the mat. The slats (also known as ordinary wood floors) and parquet floorings are constructed in different ways. There are two kinds of "real shop" and "empty shop". The "empty shop" is made up of joists, coffer boards, scissors, etc. They are generally located in the first floor room. When the joist span is large, a ridge wall should be added in the middle of the room. On the top of the ridge wall, linoleum or waterproof mortar and rimmed wood should be laid. Solid wood flooring is a wooden joist spread on reinforced concrete slabs or cushions. It is composed of wooden joists and raised plates. Door purchase Sun room Sun room Decoration Paint Room Interior Renovation Design Heating Floor tiles Fire resistance - According to the BSEN438-2/91 test, the surface of the ceramic plate has a strong protective ability against burning cigarettes. The material is flame retardant, the panel does not melt, and the properties are maintained for a long time. Antistatic – According to DIN 51953 and DIN 53482, ceramic plates have proven to be antistatic materials, making the panel ideal for use in dust-free areas, the optical industry and the computer industry. Chemical resistance - Ceramic plates have strong chemical resistance properties such as acid and oxidation resistant toluene and the like. Ceramic plates also prevent the erosion of disinfectants, chemical cleaners and food juices and dyes. They do not affect the properties of the ceramic plate or the surface. Zirconia Ceramic Plate,Ceramic Chip,Ceramic Flange,Ceramic Substrate Plate Dongguan Haikun New Material Co., Ltd. , https://www.nitrideceramic.com
1 23 Next> Total 3 Pages
Page to page