Decoration knowledge rough room brush wall steps

The rough house is also referred to as the "pre-decorated room." Most of the houses in this house have only doors and frames and no doors. The wall surface is only treated as a foundation without surface treatment. All exterior finishes outside the house, including balconies and rain covers, should be completed according to design documents. Next Xiaobian to introduce the decoration of the rough room brush wall steps.

First, preparation before construction

1. The walls should be kept dry. The surface water content should be less than 6%. The PH value should be less than 9. The new cement construction should generally be maintained for 20 days to 40 days.

2. Before the construction, the bulge must be removed, degreasing, dust removal, alkali removal, mold removal, and loose layers. In addition to washing with dilute acid water, rinse with clean water, dry and then brush the paint; in addition to mildew first use the shovel to eradicate the surface of the mold and then wash the wall water, spray two times, until dry, before brushing coating.

3. During construction, a small amount of fresh water can be added or diluted depending on the climatic conditions and the specific brushing conditions (see the instructions for use of each type for specific dosage). When the temperature is lower than 7°C and the humidity is higher than 85%, construction is not suitable.

4. Do not use polyester coating material while applying the wall paint. The ionized TDI will make the paint yellow.

5, In order to make the film durable, color retention, not subject to the violation of alkaline substances in the wall, use a sealing primer to make the bottom.

Second, the interior wall paint construction process

1. Remove dirt and dirt on the surface of wooden products and lines (wood base layer).

2. Trimming the burrs on the surface of the wood substrate, lifting the flaws, etc., and polishing with a sand leather to make the corners neat.

3, with oily putty (or transparent putty) for scraping, polishing, polishing and putty after the repair (when using varnish, brown eye, nail eye, do local color repair work).

4. Apply the paint for the first time, refill the putty, remove the surface dust after polishing.

5. Apply the paint a second time. After polishing, remove dust from the surface and apply water to the sand.

Third, the order of painting the walls

1. First, paint the ceiling away from the nearest natural light source.

2. Second, paint the walls and brush them from top to bottom, each time about two feet wide. It starts from the natural light source and then gradually moves away.

3. Then, paint the window, first from the side of the window, and finally the frame.

4. Next, paint the details, such as the panel where the wall meets the ceiling.

5. Finally, paint the skirting board.

Fourth, brush the wall need to pay attention to what

1. If you must be on schedule, add a certain amount of whitening powder to the paint. White powder can absorb the moisture in the air and accelerate the drying speed, but it will also have a negative impact on the quality of the project. So under normal circumstances, even if the humble construction team does something else or suspends work for two days, it should try not to paint when it rains.

2. The humidity of the wall should not be too large. Generally, the humidity of the wall of the latex paint application is less than 10%. If the humidity is too high, the adhesion of the paint film will be affected and the paint film will be blistering and falling off.

3. The alkalinity of the wall should not be too strong. It is generally required that the alkaline pH of the latex paint construction wall should be less than 10.

4. When painting the wall, follow the principle of vertical brushing from top to bottom, brush strokes, or lateral brushing from left to right. Do not miss the pen.

Editing summary: The steps for brushing the rough room were introduced here, and we hope to help everyone. If you want to know more related information, you can pay attention to this website information.

New house

polyurethane Sandwich Panel

polyurethane foam sandwich panel 
1. Excellent price and quality
2.Light weight Sandwich Panel
3. Good quality Sandwich Panel

 

Product name

Decorative Embossed Sandwich Panels

polyurethane sandwich panel/pu foam sandwich panel

Metal board

0.0.3mm

Core material

Hard Polyurethane foaming(for insulation)

Back layer

Aluminum foil

Standard Size

L3800*W380*H16(mm)

Packing Size

L3850*W415*H135(mm)

Quantity

8pcs /pkg or as you request

Length

3000-6000mm(1000mm, MOQ>500sqm)

Weight

3.7Kg/sqm

50Mm Eps Sandwich Panels

Eps Sandwich Panel,Pu Metal Decoration Panel,Insulation Metal Siding,50Mm Eps Sandwich Panels

Jinan Zhengtang Insulation Decoration Material Co.Ltd , https://www.ztwallsiding.com